Sloop IKARON is 30.48m and was built by Holland Jachtbouw. She was delivered in 2000 and refit in 2022.
Her hull, built in Aluminum, has a beam of 7.19m, a draft of 3.63m and was designed by Andre Hoek.
IKARON's MTU 6R 183 TE62 275 kW6 cylinder engines deliver 385 horsepower, enabling her to cruise easily at 9 knots and achieve a maximum speed of 11 knots.
Sloop IKARON can accommodate 8 guests in cabins, all looked after by a crew of 4.
IKARON is currently available for sale and is asking €2,900,000. She is available for viewings in Genoa, Italy.
Vessel Name: IKARON
Builder: HOLLAND JACHTBOUW
Model Year: 2000
Year Built: 2000
Category: Sloop
Country: Italy
MLS #: 375914
Sleeps: 8
Staterooms: 3
Crew Berths: 4
Crew Sleeps: 4
Length: 30.48 (30.48m)
Draft: 11' 11" (3.63m)
Beam: 23' 8" (7.19m)
Cruise Speed: 9 Knots
Max Speed: 11 Knots
Water Capacity: 1532.2 Gal
Manufacturer: MTU
Model: MTU 6R 183 TE62 275 kW6 cylinder
Engine Hours: 6650
Engine Type: Inboard
Horsepower: 385
• Full beam with two double beds either side
• Luxurious en-suite bathroom, with stall shower
• Two double twin cabins port and starboard forward
• Port forward cabin is equipped with an en-suite bathroom
• Two bunk cabins port and starboard
• Crew mess with U Shaped sofa, all electric controls
• Crew bathroom that doubles as an en-suite for the port forward guest cabin
• Two helm stations equipped with all sail controls
• Fantastic 360º views over and along the deckhouse
• Large table with U shaped sofa in blue leather port side
• Navigation and transmission equipment starboard side
• Steps into the upper deck salon and lower deck salon
2021
• Mast and rig pulled out of boat and all rigging removed for inspection
• All running rigging replaced
• Cabling, lights, and electronics checked, serviced or replaced
• Hydraulic furles serviced and rebuilt by Rondal
• Hydraulic halyard rams serviced
• Hydraulic aft stay tensioners serviced
• Hydraulic boom van serviced
• Mast & boom re-installed and tuned
• New Furuno radar and navigators installed
• New PC screens
• New cockpit resolution waterproof monitor
• New B&G processor and triton
• New Gyro-track compass installed
• All batteries serviced and or replaced
2022
• New electric motor
• Variable pitch gear box taken out, dismantled and serviced. All new
• Marine gearbox “Twin Disc” taken out and rebuild, new seals &
bearings.
2023
• Under water Hull sand blasted, inspected
• Propeller, shaft, variable pitch system and gear box works:
• Variable pitch propeller “Teignbridge” dismantled and serviced
• Propeller shaft pulled out, taken to machine shop. Installed in lathe,
checked for wear & torsion, cleaned. Was in perfect condition.
• Propeller shaft bearings serviced. oil and water seals, both engine
room side and water side, all replaced.
• Propeller shaft oil bath oil replaced
• Propeller shaft aft “cutlass bearing” replaced
• Main engine rubber support blocks replaced (all 2 )
• Propeller shaft & main engine re-aligned. Boat sea trials showed
perfect alignment.
• Rudder pulled out full service
• Rudder lower and upper bearings serviced
• Steering system & steering quadrant serviced
• New bearing Laghersmith
• Zink anodes new
• Brand new sails
• New tender Geniuss 320
• Hydraulic swim platform
